20' Pumpout Boats - Custom Made 20' Pump Out Boat by Marine Boatbuilders Co.We are pleased to introduce our new 2007, 20’ PUMPOUT BOAT. This is our third generation new mold. Built and designed from our 15 years of experiences building PUMPOUT boats, Work boats, and Patrol boats. Our boats are built for safety, simplicity, and stability. There is no wood in our boats, not in the hull, not in the deck, not in the transom. MODIFIED V HULL DESIGN Our PUMPOUT hull bottom is concave not convex like most hulls. This allows for maximum stability, and ease of handling. Our boat because of its design will not yaw in a following sea. The hull is constructed with a combination of hand laid woven, roving, and gun roving. All fiberglass is "E" glass and the resin is thermo set polyester. The gelcoat is ISO NPG thermo set gelcoat, normally 1.5" thick. Our boat has a 10-degree dead rise at the stern, which allow the boat to plane quickly. The hull transom is a composite laminate 1.5" thick, a total of 3" thick. There is no wood in the transom. STRINGER SYSTEM Our stringer system is a U channel all fiberglass state of the art system. There is no wood in our stringer system. Deck, Floor The deck is constructed of a combination of hand laid woven, roving, and gun roving. Fiberglass "E" glass applied and the resin is thermostat gelcoat (white). The deck is finished with non-skid on horizontal surfaces. Our deck is self-bailing at all times; weather containment is full or empty. There is NO WOOD in our deck or floor. The floor is composet fiberglass. The deck has seven, cleats, two chalks and running lights. The bow which contains one, cleat, two chalks, and running lights are all stainless pop ups. FOAMED FLOTATION Two-part thermostat foam is injected between the floor and hull in areas not occupied by tankage and other equipment. QUALITY GELCOAT Only storm and blister resistant gelcoats are used to form the skin of each PUMPOUT boat, a wide variety of colors is available. White is our standard color included in the quote price; other color choices would be extra cost. FUEL TANK The fuel tank is 50 gallons and located below the deck. CONTAINMENT CELL A built in 300 gallon fiberglass holding tank below the water line, is a standard feature on our 20’ PUMPOUT BOAT. The containment cell has five layers of fiberglass that include three layers of 18 oz. Cloth. Our containment cell has three baffles. The tank is equipped with an alarm that sounds when tank is full. PUMP We recommend an Edson pump 278EB-40 diaphragm pump, The Edson pump that runs the sewage tank and is located completely under the center console. Also under the console are intake, and discharge pipes. Leaving the entire deck free to any trip hazards and much needed additional working space. The vent is located outside the starboard hull. OTHER STANDARD FEATURES - Large size center console with windshield.
- Grab rail around windshield.
- Running lights.
- Stainless steel bow eye and transom tie-downs. (7) Ten inch S/S cleats. The cleat and chalks, as well as the running lights in the bow are pop up's. This is done for safety reasons it keeps the deck clear and free from scratching other boats.
- Two 3" scuppers.
- Heave duty rub rail
- 1100 G.P.M. automatic bilge pump. Ritchie compass
- Two deep cycle series battries, with (1) non-feed back battery switch.
- Raw water wash down pump.
- Four stowage areas with lockable doors.
- Lockable door on center console.
- Seat in front of center console.
- T-Top fiberglass top and electronic box
- Hydraulic steering (of course)
- Water proof breaker panels
- Four mushroom cleats inside deck
SPECIFICATIONS Overall length: 20’ Beam: 8’6’ Draft: 10" lightship; 12" full load Dead rise: 10 degrees Transom angle: 12 degrees Approx. weight: 1,750 lbs. Lightship HP rating: 200 single, HP recommendation: 150 HP. Freeboards: 42" forward, 27" aft. Marine Boatbuilders CO. WARRANTY We offer a five (5) year warranty on the hull and a (5) year warranty in the holding tank. This warranty applies as long as the boat is used as a Pumpout boat only.
|